Премини към съдържанието
  • Добре дошли!

    Добре дошли в нашите форуми, пълни с полезна информация. Имате проблем с компютъра или телефона си? Публикувайте нова тема и ще намерите решение на всичките си проблеми. Общувайте свободно и открийте безброй нови приятели.

    Моля, регистрирайте се за да публикувате тема и да получите пълен достъп до всички функции.

     

Препоръчан отговор


DOS стартиращо USB устройство ли се прави? 

Сподели този отговор


Линк към този отговор
Сподели в други сайтове

дискета

Сподели този отговор


Линк към този отговор
Сподели в други сайтове
преди 4 минути, DarkEdge написа:

дискета

Преди години правих DOS флашка за флашване на BIOS на лаптоп, но не се сещам с коя програма съм го правил. 

ПП с Win USB Maker правих DOS бутваща флашка. 

Сподели този отговор


Линк към този отговор
Сподели в други сайтове
преди 15 минути, DarkEdge написа:

Разопакован ли е? Трябва да има файл с bin или rom разширение
сложи ключове /O /L0

.exe; .1A0 и txt.

. rom свалих вчера от тук:

https://soggi.org/motherboards/msi/P35-Neo.htm

2008/11/11 - BIOS 1.10 / 1.A

него като се опитах да го пусна и изкара размацан син екран и не можеше да се продължи.

Мина ми идея .rom да го сложа при другите неща, ама ....не съм сигурен

 

преди 15 минути, DarkEdge написа:

дискета

нямам флопи. но и това обмислях да сваля от старите служебни и да пробвам 

Сподели този отговор


Линк към този отговор
Сподели в други сайтове
преди 3 минути, BANKATA написа:

exe; .1A0 и txt.

Да беше дал и имената на файловете...Все да си икономисате някоя написана буква. В txt naj-weroqtno е описанието на този рилийз на BIOS.


Сподели този отговор


Линк към този отговор
Сподели в други сайтове

това .txt:

1. This is AMI BIOS release

2. This BIOS fixes the following problem of the previous version:
-  Update CPU Micro Code. 
-  Fixed BIOS report incorrect CPU ratio during POST. 

3. 2008/11/11

[Below information is Chinese language]

A. AMI BIOS Ґї¦Ўµo¦ж

B. ¦№Є©Ґ»­ЧҐї¤U¦C°ЭГD:
-  §у·s CPU Micro Code.
-  ­ЧҐїҐDѕчЄO¶ґЕй¦b¶}ѕч¶Ґ¬qЕгҐЬ¤ЈҐїЅTЄє CPU АWІv.

C. §у·s¤йґБ: ¤Ѕ¤ё2008¦~11¤л11ё№
 

A това е word:

Special Note:
The BIOS and DEVICE DRIVERS contained here are exclusively for Micro-Star products only. Micro-Star assumes no responsibility for any damages resulting from improper use or lack of technical expertise.

WARNING!!!!!
DON'T FLASH FROM A FLOPPY DISK!!!!
DON'T FLASH WHEN YOUR SYSTEM IS RUNNING FINE!!!!
DON'T FLASH IF YOU DON'T KNOW WHAT YOU ARE DOING!!!!

Award BIOS Flash Procedure

1. Know your model number

a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (Some motherboards are named like K8N Diamond; make sure you have the right version number)

b. Boot up your system & take a look at the top left screen during POST, you should see something like “W7100NMS V1.1 021705” This means the board is MS-7100 with BIOS version 1.1

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, and you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

2. Download the BIOS that matches your motherboard AND version number (some motherboards are named like K8N Diamond; make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is AMD 939 type then look here

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_list.php?kind=1&CHIP=68&NAME=Socket%20939%20(AMD%20K8)

if you cannot find the BIOS that matches your board, try here http://www.msi.com.tw/support/bios/more.php 

3. Extract the BIOS-archive that you have downloaded by double clicking to c:\test
4. Boot your system from a Win98 or WinME boot-floppy.

How to make boot floppy in case your don’t have it ready:

For Win9X, You can type [C:\ format a:/s] from the DOS prompt.
For WinME, You can make a boot floppy from control panel--> add/remove program-->make boot floppy. Remove autoexec.bat & config.sys file if there's any.
For Win2000, there's no way to make boot floppy, so you have to either use Win9X or WinME boot floppy.

For WinXP, you can make a DOS boot disk. Go to Your Computer, right click drive A:, select Format, select copy system files. 

5. When you get the A:\ prompt, type the following sequence:
😄 <enter>
cd\test <enter>

C:\test> awdfl865 BIOS file

(To save or not to save old BIOS is the user’s decision)
6. Reboot your system when prompted 

AMI BIOS Flash Procedure

1. Know your model number

a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like 945G Neo2, make sure you have the right version number)

b. Boot up your system & take a look at the top left screen during POST, you should see something like “MSI 945P/G Neo 2 A7176IMS V3.3 Date: 04/26/06” This means the board is MS-7176 with BIOS version 3.3

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

2. Download the BIOS that matches your motherboard AND version number (some motherboards are named like 945G Neo2, make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is Intel 775 type then look here

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_list.php?kind=1&CHIP=67&NAME=Socket%20775%20(Intel%20P4)

if you cannot find the BIOS that matches your board, try here http://www.msi.com.tw/support/bios/more.php

3. Extract the BIOS-archive that you have downloaded by double clicking to c:\test
4. Boot your system from a Win98 or WinME boot-floppy.

How to make boot floppy in case your don’t have it ready:

For Win9X, You can type [C:\ format a:/s] from the DOS prompt.
For WinME, You can make a boot floppy from control panel--> add/remove program-->make boot floppy. Remove autoexec.bat & config.sys file if there's any.
For Win2000, there's no way to make boot floppy, so you have to either use Win9X or WinME boot floppy.

For WinXP, you can make a DOS boot disk. Go to Your Computer, right click drive A:, select Format, select copy system files. 

5. When you get the A:\ prompt, type the following sequence:
😄 <enter>
cd\test <enter>

C:\test> adsfi719 BIOS file

(to save or not to save old BIOS is the user’s decision)

6. Reboot your system when prompted

Flashing the BIOS for Non-FAT file system

1. Know your model number
a. Open your case and look for the MS-XXXX number on the motherboard between the PCI slots, also check the version number that is written there as well. (some motherboards are named like K8N Diamond, make sure you have the right version number)
b. Boot up your system & take a look at the top left screen during POST, you should see something like
“W7100NMS V1.1 021705” This means the board is MS-7100 with BIOS version 1.1

Hint: Many systems are clearing this message very fast, the bios version is then unreadable, and you can either press “PAUSE” or disable the “Quick Boot” in the BIOS setup.

3. Download the BIOS that matches your motherboard AND version number (some motherboards are named like K8N Diamond; make sure you have the right version number). BIOS can be found according to the CPU type of your board like if your CPU is AMD 939 type then look here
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_list.php?kind=1&CHIP=68&NAME=Socket%20939%20(AMD%20K8)

if you cannot find the BIOS that matches your board, try here <http://www.msi.com.tw/support/bios/more.php>

4. Extract the file you have downloaded to a floppy (not the win ME/98 startup floppy) by double clocking the file in windows mode and supplying the path a:\

5. Boot the computer using windows ME or windows 98 startup disk. It must be one of these! A plain boot disk will not be good enough.

If you do not have Windows ME or 98 to create the floppy you can make one on a friend's computer. 

6. When boot is done there will be a message on the screen showing:"Diagnostic tools were successfully loaded to drive" followed by a single letter.

This letter is the letter assigned to the RAMDRIVE. This RAMDRIVE is a virtual drive in the system memory and can be accessed and controlled like any other drive with DOS commands such as:

MD - Make Directory

Copy - copy a file

Delete - Delete a file 

There is one important difference which is that being in the system memory this drive is wiped once the computer is restarted or shut down.

7. Replace the startup floppy with the one containing the flash utility and bios ROM files previously extracted in windows. 

8. Copy the 2 files to the RAMDRIVE by using the DOS command copy.

Here is an example, in this example the flash utility is AWFL865.EXE ,the ROM file is  W7100NMS.110  and the RAMDRIVE letter assignment is D 

copy awfl865.exe d:\

copy w7100nms.110 d:\ 

9. Change the current working directory to the RAMDRIVE root directory, with the example case of the RAMDRIVE being drive D this is done by simply done with the command d:

10. Execute the flash utility with the ROM file as a command line argument, with this example:

awfl865 w7100nms.110 

If you wish to save the current bios you must specify the full path a:\filename. Specifying only a file name will save the bios to the RAMDRIVE which will be wiped after restarting the computer and the file will not be saved. 

a:\bios.old is an example of the correct way to save the bios. 

11. Reboot your system when prompted

12. If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described

Сподели този отговор


Линк към този отговор
Сподели в други сайтове
преди 1 минута, BANKATA написа:

WARNING!!!!!
DON'T FLASH FROM A FLOPPY DISK!!!!
DON'T FLASH WHEN YOUR SYSTEM IS RUNNING FINE!!!!
DON'T FLASH IF YOU DON'T KNOW WHAT YOU ARE DOING!!!!

Виж колко добре са си го написали хората
НЕ ФЛАШВАЙТЕ ОТ ФЛОПИ
НЕ ФЛАШВАЙТЕЕ, АКО СИСТЕМАТА РАБОТИ ДОБРЕ
НЕ ФЛАШВАЙТЕ, АКО НЕ ЗНАЕТЕ КАКВО ПРАВИТЕ

Сподели този отговор


Линк към този отговор
Сподели в други сайтове

Да видях го това. аз го мъча два дни с флашка.

 

Това ме наведе на мисълта за флопи:

4. Boot your system from a Win98 or WinME boot-floppy.

How to make boot floppy in case your don’t have it ready:

For Win9X, You can type [C:\ format a:/s] from the DOS prompt.
For WinME, You can make a boot floppy from control panel--> add/remove

Сподели този отговор


Линк към този отговор
Сподели в други сайтове
Гост

като гледам, като че ли не знаеш какво правиш
но ако си решил да експериментираш с риск да увредиш системата
в предишния пост, дето си постнал текста е написано, че става така
copy Afud408.exe d:\
copy A7360IMS.1A0 d:\
d:\Afud408 A7360IMS.1A0
където d: ти виртуален дял
а за да запазиш старият биос a:\bios.old
където a: ти е флашката
ясно осъзнавам, че може да го развалиш, но може би това е твоята идея

Сподели този отговор


Линк към този отговор
Сподели в други сайтове

Във форума на MSI намерих тема за "ami bios flash procedure 7360"  ( https://forum-en.msi.com/index.php?topic=116721.0 ), и стана много лесно.

Новия процесор си тръгна без проблеми.

Благодаря ви за отделеното време.

Сподели този отговор


Линк към този отговор
Сподели в други сайтове

Добавете отговор

Можете да публикувате отговор сега и да се регистрирате по-късно. Ако имате регистрация, влезте в профила си за да публикувате от него.

Гост
Напишете отговор в тази тема...

×   Вмъкнахте текст, който съдържа форматиране.   Премахни форматирането на текста

  Разрешени са само 75 емотикони.

×   Съдържанието от линка беше вградено автоматично.   Премахни съдържанието и покажи само линк

×   Съдържанието, което сте написали преди беше възстановено..   Изтрий всичко

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Добави ново...