Проблем с преинсталация.

[alf000]

Няколко пъти вече си преинсталирам компютъра от диск с Уиндоус 10. Всичко точно, докато вчера не ми се наложи да преинсталирам пак, но този път с следнатс грешка.

 

Компютъра си е със същите части както и преди, диска не е изхабен за да не го чете.

 

За тези който ще ми предложат УСБ/флаш памет, ми няма да може, защото мойте вградени са прецакани и съм с пи-си-ай към усб за да мога да ползвам усб неща, проблема е,че те се вкчват едва след когато трябва да бутне от флаш паметта.

[Joss Bomon]

Повредено оптично устройство, повреден носител, проблемен хард диск, кабели за данни...

[Proshark]

Fix Error Code 0x800701E3 on Windows 11/10 during Windows Setup

Spoiler

While a Windows 11/10 upgrade is going on, a number of components take part in this process. There is the Network, CPU, Disk, and even more. Thus, it makes the process of upgrading Windows intensive. However, if there is an obstruction in your upgrade process, you could end up seeing error code 0x800701E3. This is caused mainly due to the ‘disk’ part of this whole process. It is caused due to a conflict with the storage of the computer.

Windows cannot install required files. Make sure all files required for installation are available, and restart the installation. Error code: 0x800701e3.

Today, we will be discussing how to fix error 0x800701E3 during Windows 10 Setup.

Error code 0x800701E3 during Windows Setup

To resolve this error code 0x800701E3, we will be carrying out the following fixes:

1. Delete System Files related to both the components.
2. Use System File Checker and DISM.
3. Use CHKDSK.

Exit the setup process and boot normally into your Windows.

1] Delete System Files related to both the components

Some residual junk system files like Cache files and driver residue can block an upgrade. Hence, I would recommend you to run Disk Cleanup to delete the files and data that is safe to be removed from your computer. The main files that you need to remove here should be Previous Windows Installations.

You can also use third-party software like CCleaner to clean up System and Registry junk that might be causing a conflict.

 

2] Use System File Checker and DISM

Run CMD as Administrator and then execute the following command to run System File Checker:

sfc /scannow

Restart your system after the scan is completed.

You can also use our freeware FixWin to Run the System File Checker utility with a click.

Now, to fix Windows Update files using DISM, open Command Prompt (Admin) and enter the following three commands sequentially and one by one and hit Enter:

 

Dism /Online /Cleanup-Image /CheckHealth
Dism /Online /Cleanup-Image /ScanHealth
Dism /Online /Cleanup-Image /RestoreHealth

Let these DISM commands run and once done, restart your computer and try again.

 

3] Use CHKDSK

To run ChkDsk, open This PC. Right-click on your Operating System Partition for Windows and select Properties.

Navigate to the tab labeled as Tools. Under the section for Error Checking, click on Check.

A new mini window will now pop up. Click on Scan drive.

Let it scan your disk drive partition and after that reboot your computer for the changes to take effect.

 

[цър-вул]

преди 58 минути, alf000 написа:

Няколко пъти вече си преинсталирам компютъра от диск с Уиндоус 10.

1. Това в среда на инсталиран Windows 10 ли се случи или зареди системата от външен носител и възникна този проблем?

[alf000]

преди 56 минути, цър-вул написа:

1. Това в среда на инсталиран Windows 10 ли се случи или зареди системата от външен носител и възникна този проблем?

не, това се случва след като Уиндоус копира файловете започва да ги инсталира, но след 1% е тази грешка.

преди 1 час, Proshark написа:

Fix Error Code 0x800701E3 on Windows 11/10 during Windows Setup

  Покажи скритото съдържание

While a Windows 11/10 upgrade is going on, a number of components take part in this process. There is the Network, CPU, Disk, and even more. Thus, it makes the process of upgrading Windows intensive. However, if there is an obstruction in your upgrade process, you could end up seeing error code 0x800701E3. This is caused mainly due to the ‘disk’ part of this whole process. It is caused due to a conflict with the storage of the computer.

Windows cannot install required files. Make sure all files required for installation are available, and restart the installation. Error code: 0x800701e3.

Today, we will be discussing how to fix error 0x800701E3 during Windows 10 Setup.

Error code 0x800701E3 during Windows Setup

To resolve this error code 0x800701E3, we will be carrying out the following fixes:

1. Delete System Files related to both the components.
2. Use System File Checker and DISM.
3. Use CHKDSK.

Exit the setup process and boot normally into your Windows.

1] Delete System Files related to both the components

Some residual junk system files like Cache files and driver residue can block an upgrade. Hence, I would recommend you to run Disk Cleanup to delete the files and data that is safe to be removed from your computer. The main files that you need to remove here should be Previous Windows Installations.

You can also use third-party software like CCleaner to clean up System and Registry junk that might be causing a conflict.

 

2] Use System File Checker and DISM

Run CMD as Administrator and then execute the following command to run System File Checker:

sfc /scannow

Restart your system after the scan is completed.

You can also use our freeware FixWin to Run the System File Checker utility with a click.

Now, to fix Windows Update files using DISM, open Command Prompt (Admin) and enter the following three commands sequentially and one by one and hit Enter:

 

Dism /Online /Cleanup-Image /CheckHealth
Dism /Online /Cleanup-Image /ScanHealth
Dism /Online /Cleanup-Image /RestoreHealth

Let these DISM commands run and once done, restart your computer and try again.

 

3] Use CHKDSK

To run ChkDsk, open This PC. Right-click on your Operating System Partition for Windows and select Properties.

Navigate to the tab labeled as Tools. Under the section for Error Checking, click on Check.

A new mini window will now pop up. Click on Scan drive.

Let it scan your disk drive partition and after that reboot your computer for the changes to take effect.

 

има  два носителя на памет хард диск и ССД, опитва да инсталирам на ссдто което е форматирано 

преди 1 час, Joss Bomon написа:

Повредено оптично устройство, повреден носител, проблемен хард диск, кабели за данни...

засега изключвам тези повреди.

изключих и пак включих ссдто от кабелите и засега тръгна да се преинсталира Уиндоуса. благодаря

[цър-вул]

преди 1 час, alf000 написа:

не, това се случва след като Уиндоус копира файловете започва да ги инсталира, но след 1% е тази грешка.

Направи следното - зареди от диска и като зададеш език/регион, натисни [Shift]+[F10]. В черния прозорец напиши:
diskpart
lis vol
exit 
Виж си буквата на дяла с Windows
Напиши
chkdsk "c:" /b
и натисни [Enter]
Изчакай да завърши проверката.
Ако завърши напиши exit и продължи с инсталирането.

[alf000]

благодаря ви, тръгна като го разкачих първо от жиците.друго не съм пробвал, благодаря